Hybrid View
-
08-28-2010 10:36 PM #1
I would also welcome any input from Pat or Jerry or anyone else who wants to critique these combinations. I just did these to show that you really can make big power for cheap with a BBC tall deck block.
Cheapo BBC 505 tall deck grunt motor
I'm always interested in researching street/strip combinations that are easy on the budget. This is a combo based on the tall deck 427T block. The block deck height of this block is 10.200", 0.400" taller than a regular production 396/427/454 block. The total combined stack measurement of parts I've used here is 10.185", leaving 0.015" nominal piston deck height on a virgin block. I'd check the decks for being square with the centerline of the main bearing bore and if they were, I might leave them alone and use a gasket such as 0.041" compressed thickness for a squish of 0.056". You can put this same motor together using a standard production 427 or 454 block, you just use 6.135" rods instead of the 6.535" rods used in this build and forget about the spacer plates.
http://www.summitracing.com/parts/FPP-1071/
Scat cast steel 4.250" crank....
http://www.summitracing.com/parts/SCA-945420/
Eagle 6.535" rods....
http://www.jegs.com/i/Eagle/356/CRS65353D/10002/-1
TRW H112CP+.100 hypereutectic pistons...
http://www.flatlanderracing.com/trwchevyspecial.html
Read across the chart for effective static compression ratios with different chamber volumes....
This makes a 505 in a tall deck block for cheap.
Continuing with relatively cheap....
Racing Head Service cast iron heads, 119cc chambers for 10.2:1 static compression ratio....
http://www.summitracing.com/parts/RHS-11301-02/
Published head flow factored by 0.90...
.100 68 56
.200 149 106
.300 221 144
.400 278 176
.500 306 206
.600 324 223
.700 338 239
Use these Moroso rectangular port spacer plates between heads and intake manifold, using Edelbrock #7202 intake gaskets on each side of the plates....
http://www.summitracing.com/parts/MOR-65090/
Edelbrock RPM intake for rectangular ports...
http://www.summitracing.com/parts/EDL-7163/
Or this RPM Air Gap for rectangular ports....
http://www.summitracing.com/parts/EDL-7562/
Or this Weiand Stealth for rectangular ports....
http://www.summitracing.com/parts/WND-8018/
The following DynoSim pulls were made with large-tube, equal-length headers through mufflers and an 850 carb....
More than one professional engine builder has advised that big block Chevies eat flat tappet camshafts, so be aware. I have composed three different pulls, with the only changes being the cam. One hydraulic flat tappet, one hydraulic retro-fit roller tappet and one solid flat tappet combination. I didn't build these to be race motors, but rather low-buck street/strip grunt motor combinations that nose over at 5500. I went through about half a dozen cams on each combination and am publishing the best results here.
I'll run the retro-hydraulic roller motor first. I used 1.8 rockers with it for a new lift of .552"/.572"...
CompCams XR288HR, part number 11-433-8
http://www.summitracing.com/parts/CCA-11-433-8/
RPM HP TQ
2000 193 508
2500 245 515
3000 311 544
3500 386 579
4000 455 600
4500 508 593
5000 546 573
5500 555 530
6000 490 429
Peak volumetric efficiency 97.6% @5000
Peak BMEP 178.2 @4000
This combo uses a hydraulic flat tappet cam with stock 1.7 rockers...There are those on this board who will advise against using a flat tappet camshaft in a BBC, including the author.
CompCams XE284H, part number 11-250-3
http://www.summitracing.com/parts/CCA-11-250-3/
RPM HP TQ
2000 195 512
2500 247 519
3000 314 550
3500 394 591
4000 470 617
4500 533 622
5000 581 611
5500 600 570
6000 589 516
Peak volumetric efficiency 100.9% @5000
Peak BMEP 185.6 @4500
Now here's one for those of you who don't mind checking valve lash maybe twice a year, although you could probably stretch it to yearly with the technology used today. Back in the day, this used to be a frequent chore, but not so much today. See, the thing is that once you get the lash set properly with the motor hot, you allow it to cool and check where the lash is. Then you can set it cold from then on and encounter no muss or fuss.
CompCams 288CR-8, part number 11-713-9
http://www.summitracing.com/parts/CCA-11-713-9/
Used stock 1.7 rockers. You'll need more spring in the heads to run this cam. Cylinder head part number I listed above has max lift of 0.600". This cam has 0.714" lift.
RPM HP TQ
2000 192 503
2500 246 517
3000 314 551
3500 403 605
4000 492 646
4500 573 670
5000 635 667
5500 673 642
6000 680 597
6500 659 533
Peak volumetric efficiency 98.3% @5000
Peak BMEP 199.7 @4500Last edited by techinspector1; 08-28-2010 at 11:54 PM.
-
09-07-2010 05:53 PM #2
to techinspector1 would i have to run diffrent pistons if i ran a blower and nitrious.
-
09-07-2010 05:56 PM #3
I wore a camouflage T-shirt once. The response in the pub was "Oooh, it's a floating head!" .
the Official CHR joke page duel