what rings do you use? ive always used hastings rings and clevite 77 bearings. but i am taking the hint that hastings must not be to high performance since jegs and summit dont have them :LOL: ;)
Printable View
what rings do you use? ive always used hastings rings and clevite 77 bearings. but i am taking the hint that hastings must not be to high performance since jegs and summit dont have them :LOL: ;)
A good moly ring is all you need for a bracket type engine.Quote:
Originally Posted by gassersrule_196
I would not buy the cheap sealed power rings I also would not buy the plasma moly rings because it will take forever for them to seat and the cost to much.
We have used the Speed Pro Moly ring sets that sell for about $40 in all the SBC in the 300 to 500 hp area.
I don't even look at the plasma moly rings until they say 250 shot of N20 or blower with 10 lbs. of boost or if they say 13.5 to 1 or more.
Speed Pro or Total Seal. Now PBM does have very good set of High Performance rings for little less.
I will second the PBM rings.Quote:
Originally Posted by Racecar100
They sell for about $75 to $80 "customer cost" in "file - fit" or non file fit.
I have used them in some drag cars with a 200 shot of N20 with no problems after 125 + pass's.
Total Seals.... always ran Total Seals, A few years ago I let my machinist talk me into some other brands in my Fontana midget motor because he said Total seals wear the bores. Well midget engines are laid over 45 degrees and have a drain hose from the valve cover back to the oil pan,needless to say his favorite brand of rings would not seat and had so much blow by that it looked like an oil well out of the remote breather tank. After several attempts to seat em I gave up,pulled the engine out and put my beloved Total seals in and had instant seal.
I just bought a set of federal mogul 'sealed power' E-245 K60 for my 292,(slowly-but-slowly:LOL: ) I'm getting all the parts together.
But I'll do good to see 300 hp with this build,so they may be ok for a mild smallblock,CR will be around 9:1 and it's an occasional street vehicle.
If your running high CR and/or high HP then get the best.
As a matter of fact my machine shop won't hone for 'cast' rings because of all the junk on the market.He said 'good moly rings'.
But,,,the rings(no matter the cost) will work in the more important area than rings,,,,thats the bore.If it ain't straight/round/proper honed then the rings can't work right,but that wouldn't justify using cheap rings,just my 2 cents worth.
i use the PBM rings i think there mahle and for mild engine hasting moly if a hi hp JE or speed pro
Yes,the PBM rings are Mahle along with the PBM pistons.Quote:
Originally Posted by pat mccarthy
yep use them both pistons / ring s use alot of there stuffQuote:
Originally Posted by erik erikson
since when did rings get so expensive :LOL: :CRY:
rings c&a, hellfire, ts. bearings calico
I like the Total Seal...Heard all the stories about cylinder wear, but haven't had the problem yet.... Also though, the last stroker I put together came with Mahle pistons and rings...No problems with them either...
i am happy :D with the ones that seal**) **) **) **) **) **)
Is that an unusual event with them chebbies???????:LOL: :LOL: :LOL: :LOL: :LOL:Quote:
Originally Posted by pat mccarthy
BAD DAVE,BAD DAVE.:LOL:Quote:
Originally Posted by Dave Severson
wells i ordered hastings mahle's so i hope they work :LOL:
Hastings and Mahle are two different companies.Quote:
Originally Posted by gassersrule_196
Do you mean moly rings??
ahh yes you say tomayto i say tomatoe i say mahle you say moly? :LOL: yes moly. i really should pay more attention course most of my posts are at 1 am !
Make sure you tell your machine shop that you are going to run moly rings so they can put the right finish hone on your block.Quote:
Originally Posted by gassersrule_196
i use a plateau brush on miss moly:D
i have two one just a brush uf-450 $55.79 at goodson and one that runs on a sunnen AN hone head goodson is were i got mine . no i do not have a used ones. but if i see one i will let you know. about 5 passes down the hole and your good . i go from AN 301 and hop up to the N37-j85 about the same passes with them to . and i go to the brush
yes the smaller ones are less that was for a 4.000 -4.500 but have used it many times on the 4.600 boresQuote:
Originally Posted by DennyW
thats not bad deal if not a screw up on there part ?