12 degrees baseline-37 with vacuum???

[tcodi]

I just put in a summit hei distributor and set it up with the vacuum plugged and set the baseline to around 12. When I hooked the vacuum up to the full manifold port on my carb it went up to almost 40 degrees.
The idle ran great like that, but is this too much? Is the vacuum can supposed to put that much advance on it?

I also tried using the timed vacuum port and in that case at idle it didn't do much but if I cracked the throttle at all it would jump up to about the same point. Will I hurt anything by running this much vacuum advance if I use the manifold port?

[lt1s10]

I just put in a summit hei distributor and set it up with the vacuum plugged and set the baseline to around 12. When I hooked the vacuum up to the full manifold port on my carb it went up to almost 40 degrees.
The idle ran great like that, but is this too much? Is the vacuum can supposed to put that much advance on it?

I also tried using the timed vacuum port and in that case at idle it didn't do much but if I cracked the throttle at all it would jump up to about the same point. Will I hurt anything by running this much vacuum advance if I use the manifold port?

i've run it both ways, according to what i wanted it to do. if you leave it ported then you can pull your base timing lower (5 degrees) for better starts. ported vac. retards the timing when you crack the throttle and the timed vac., adv. the timing when you crack the throttle. i'd try it both ways and see which one works better. someone will come along and say you can't do that, but they are wrong.

[Dave Severson]

I'm with Mike, I'd do as he suggested, then use the timing that works best for you engine, car weight, etc. 37 total is high, watch and listen closely for detonation.

[lt1s10]

I'm with Mike, I'd do as he suggested, then use the timing that works best for you engine, car weight, etc. 37 total is high, watch and listen closely for detonation.

if he back up to 5 degrees on the base dave, then 32 want be bad. his total is probanly around 37.

[Dave Severson]

Yup, 32 total and 5 intitial would make for easier starting and less prone to deonation on the big end.

[C9x]

Ported vacuum and timed vacuum are the same thing.
Obtained from above the throttle blades.

Full time and manifold vacuum are the same thing.
Obtained from below the throttle blades.

Lots of advance at idle is good because it takes time to burn the lean idle mixture.
The great majority of engines will run hot in traffic or at idle on hot days - and cold ones as well - if the vacuum advance source vacuum is selected to ported vacuum.

Ported vacuum and manifold vacuum both retard the timing when the throttle is depressed.
It may help to view the vacuum advance cannister as a vacuum retard device.

Rpm controls the mechanical - or centrifugal timing - nothing else affects it.

Load controls the vacuum advance due to varying vacuum levels of the engine.
Except at idle when ported vacuum shows zero and manifold vacuum shows full vacuum - 17" - 19" with a stock or very mild cam - the vacuum levels of both ported and manifold vacuum follow each other fairly close.

Mechanical and vacuum advance systems overlap each other depending on engine load and rpm so as to give you the proper amount of advance for a particular situation.


When you time the engine the vacuum advance line should be disconnected and plugged at the distributor end . . . golf tees work great for this.
If you set total all-in timing with the vacuum advance line connected to manifold vacuum you'll be giving away a lot of horsepower.
Same thing is true with ported vacuum although to a lesser extent since it takes a bit of rpm to get ported vacuum up to full vacuum levels.

[tcodi]

when I checked the total with the vac plugged it would go up to around 35 or so. I liked the way it idled better with the full vac but the guy at summit said I would burn pistons if I used 40 at idle. Obviously as I get on the gas in this case it would drop off quickly and my total would be a little less than that.
Well, you are right about some people saying I can't do it. I guess I'll just play with variations until it works well.

[C9x]

when I checked the total with the vac plugged it would go up to around 35 or so. I liked the way it idled better with the full vac but the guy at summit said I would burn pistons if I used 40 at idle. Obviously as I get on the gas in this case it would drop off quickly and my total would be a little less than that.
Well, you are right about some people saying I can't do it. I guess I'll just play with variations until it works well.

Burning pistons at idle is a new one on me.

More than likely something that never happened.

Nothing against Summit, I like them and trade with them, but like anyplace else some employee's know what they're doing and others are passing along what they think . . . right or wrong.


Got a Motor's Manual?

Do a little digging in there and you'll find both mechanical and vacuum advance curves. (Keep in mind some of the figures listed are in distributor degrees so you'll have to double them for total crankshaft timing.)
A little extrapolation to fit your needs and you'll be in business.

[Mikej]

You can get an ajustable vaccum can. The one you you have must be 25 deg. adv. If you also at 20 deg of mech. That is a total of 57. What is your total at 3000 rmp? What is it at 3000 rpm with the vaccum unhooked?
Port vaccum increases as you accellerate, but can also cause the car to run hot at idle. Not enough vaccum advance.

[tcodi]

yeah but the vac and mechanical wouldn't stack up, when mech's full on the vac is off