Printable View
Hi all, im new here and new to the 385 ford family im mostly an fe guy but my son wants to put a 429/460 in his mustang were building and would like in the range of 600+ lbs of torque for this will be raced but also i might add were on a budget so my questions are 1. how do you tell the years of these 2.ive heard that some of these are internally balanced and others arent 3. what kind of cars can the ones you recommend be found in and year of car thanks fordbeast.
The available production cast iron block casting numbers are C8VE-A, C9VE-A, D0VE-A, D1VE-("xxx") and D9TE-AB.Quote:
Originally posted by fordbeast
Hi all, im new here and new to the 385 ford family im mostly an fe guy but my son wants to put a 429/460 in his mustang were building and would like in the range of 600+ lbs of torque for this will be raced but also i might add were on a budget so my questions are 1. how do you tell the years of these 2.ive heard that some of these are internally balanced and others arent 3. what kind of cars can the ones you recommend be found in and year of car thanks fordbeast.
I like to refer to all but the D9TE as the "early-style" blocks. The D9TE casting arrived in the 1979 model year and was utilized until the end of 460 production ( to 1996).
For the most part, all blocks and rotating asemblies are interchangable between all blocks except the D9TE. A D9TE rotating assembly will fit into an early-style block, but the opposite is not true.
All 429/460 Fords are internally balanced engines except for the D9TE 460, which is externally balanced. This means that all engines until 1978 are internally balanced.
These block identifying marks (D1VE, etc.) are not actual casting numbers but are engineering revisions that are cast into the block castings themselves. And they are what we enthusiasts refer to when identifying our factory iron, as they give not so much the year that the block was made but rather the revision of the block as specified by said engineering revision. (Actual date code is in the lifter valley.)
Early-Style Blocks: For the most part (and with small exception), the C8VE, C9VE and D1VE blocks are all essentially the same configuration casting with the thinner main webs. The thicker main web block is the D0VE block, which may or may not have 4-bolt main caps on 2,3 & 4. (Very few D1VE blocks may be thick webbed.) All Ford production 385 blocks can be decked as needed, so this is a non-issue detail.
D9TE Blocks: The externally balanced rotating assembly utilizes a crankshaft that has slightly smaller counterweights. This was done to so that the cylinders of the D9TE block could be extended about .1875" deeper towards the crankcase. I believe the cylinders were lengthened in the D9TE block because this block was revised to double as a big equipment truck block, and the dump truck rotating assemblies consisted of a very deep skirt piston that benefitted from the extended cylinder walls for support.
The deeper cylinders of the D9TE blocks are the reason that the early-style, internally balanced rotating assemblies will not fit (internal balance crank throws will not clear D9TE cylinders).
Since most prefer to use internally balanced rotating asembies in the performance applicaton, we usually opt for any block except the D9TE. There are also advantages to specific blocks within the group of early-style blocks, such as the D0VE-A's thick main webs, thick pan rails on some early-style blocks, etc.
Further, the D9TE block was presumed to be a lightweight ("late model") casting and therefore not very strong and also limited in it's overbore capability. But this belief is currently being re-evaluated for a couple of reasons:
- No-one had yet evaluated D9TE cylinder wall thickness with a sonic checker, and preliminary testing suggests the block may not be so bad afterall.
- Strokers have become popular and the D9TE's deeper cylinders offer more support for the increased-stroke rotating assemlies.
- Most all aftermarket stroker kits use a crank with the dimensions of the externally balanced crank and so they fit the D9TE block as well as the early blocks.
The most common carbureted head casting numbers are: C8VE-A, C9VE-E, D0VE-A, D0VE-C, and D3VE-A2A.
All the above heads have 2.08 intake valves and 1.65 exhaust valves.
C8VE-A, C9VE-E, D0VE-A, & D0VE-C all have identical architechure, are completely interchangable and have 75-77cc combustion chambers. These are the most popular factory heads for performance applications.
D3VE-A2A's have a 96cc combustion chamber and a different valge train assembly that is not interchangable between it and the other heads. They can be made to work well but require more prepping.
Ther is also the D0OE-R Cobra jet heads (nice but rare) and the D2VE-AA heads (JUNK).
The heads and valve trains are all swappable between the blocks.
There is no such thing as 2-bbl and 4-bbl heads...they are the same thing.
Getting 600 foot pounds of torque from a stock stroke 460 is asking a lot unless you intend to put a blower on it. Another option is a stroker kit that can add loads of torque to a normally aspirated engine.
Paul