Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: pulley sizing
          
   
   

Reply To Thread
Results 1 to 5 of 5

Hybrid View

  1. 01-14-2005 07:39 AM #1
    shawnlee28's Avatar
    shawnlee28
    shawnlee28 is offline CHR Member
    Visit my Photo Gallery
    Join Date
    May 2004
    Location
    so.cal
    Car Year, Make, Model: 66 c 10 fleetside longbed
    Posts
    1,942

    Question pulley sizing

     



    Whats the approx size of a small block water pump pulley?Or should I use the biggest 1 I can fit on there ?
    Last edited by shawnlee28; 01-14-2005 at 07:43 AM.
    Its gunna take longer than u thought and its gunna cost more too(plan ahead!)
    Reply With Quote Reply With Quote
  2. 01-14-2005 10:11 AM #2
    Henry Rifle's Avatar
    Henry Rifle
    Henry Rifle is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Apr 2004
    Location
    Little Elm
    Car Year, Make, Model: 34 Ford Low Boy w/ZZ430 Clone
    Posts
    3,890

    Just get the one that fits your water pump (long or short).

    Denny,

    You're right. It's about 7" Just measured mine.
    Jack

    Gone to Texas
    Reply With Quote Reply With Quote
  3. 01-14-2005 11:39 AM #3
    Stu Cool's Avatar
    Stu Cool
    Stu Cool is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Oct 2003
    Location
    Olivehurst, CA
    Car Year, Make, Model: '53 Studebaker Custom w/LS1
    Posts
    1,900

    As a side note, there is a dual groove water pump pulley that has 2 different diameters. It must be used with a crank pulley that also has 2 different diameters. The larger pulley groove is for the alternator to overdrive it to maintain output at lower RPM.

    Pat
    Of course, that's just my opinion, I could be wrong!
    Reply With Quote Reply With Quote
  4. 01-14-2005 05:32 PM #4
    shawnlee28's Avatar
    shawnlee28
    shawnlee28 is offline CHR Member
    Visit my Photo Gallery
    Join Date
    May 2004
    Location
    so.cal
    Car Year, Make, Model: 66 c 10 fleetside longbed
    Posts
    1,942

    Thumbs up

     



    THnx all!! I just went and measured 7 inches.I just thought it was a little close to the crank pulley ,theres only about the width of a nickle between em.
    Its gunna take longer than u thought and its gunna cost more too(plan ahead!)
    Reply With Quote Reply With Quote
  5. 01-14-2005 06:21 PM #5
    Henry Rifle's Avatar
    Henry Rifle
    Henry Rifle is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Apr 2004
    Location
    Little Elm
    Car Year, Make, Model: 34 Ford Low Boy w/ZZ430 Clone
    Posts
    3,890

    The pulleys are pretty close. There's about 5/16" between the pulleys on my motor.
    Jack

    Gone to Texas
    Reply With Quote Reply With Quote
Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules

Links monetized by VigLink