Thread: chevy stock roller cams ID

Tweet

doing a low dollar 350 a guy has some used stock roller cam s i can not seam to find the grind no in gm parts books short of putting each can up on v blocks or in the block any one know were i can find the full list of gm hyd roller cams the one i think i am going to use is a marine bc395 (bay city)? blue paint on the back looks like maybe 450/432 lift THANKS

Check out this OE 87-94 fit Roller Camshaft . http://www.competitionproducts.com/p...p?number=E1136

could be good that cam lift looks about rigth but the cam i have is going to get used i will do the dur @ 050 in the block he has no money so that the cam he going to get and like it he can recam it when he gets more coin i called them they have a better deal s and i am a dealer thru them but he has nO coin

This might be the Camshaft you have . 14097395 Hydraulic Roller Design
This hydraulic roller design is used on the 383 truck. The duration at lash point in degrees (intake/exhaust) is 288/308; duration at .050” tappet lift (intake/exhaust) is 196/206; and maximum lift with 1.5:1 rocker ratio (intake/exhaust) is 431/451. Valve lash is zero/zero and lobe centerline is 109 degrees.

it a used marine cam hard to say if it was used in that engine . alot of them were made in bay city here less then 10 miles from here i will know when i check the dur

Back 20 some years ago when I worked in Farwell, Mi.
I'd have guy's come in with stuff they wanted built.
Stuff was never what they thought it was.
A guy brought in a cam for a chevy, the cam end up being for a
Ford and the springs were for a Dodge, I don't remember what the
lifters were for. Kurt

i have guys drop off stuff and say make it work .just another one of them deals were i am going to use this roller cam i have come up with . then take money out of my labor to buy him a new roller cam . this cam is the best i can find for him cheap. he has lost two flat lifter hyd cams and i am not going to re build this engine and hear that he s wipe a cam out of a engine i built him .they built it the first time and had some bad machine work done they did just about every thing you could do wrong on it .i feel they can not break in a new flat lifter cam if i put one in it so it a roller

Scoggins-Dickey has a good listing of them. I used a GM roller cam that I bought from them called the Ram Jet roller cam in a TBI rebuild and was really happy with the results. I think it was about $200.

I've do have a cam Doctor and will be able check your cam to find duration lifts Center line

Originally Posted by Racecar100

I've do have a cam Doctor and will be able check your cam to find duration lifts Center line

thanks i have one if i needed it . i can do duration with a dur wheel i have the lift i think i got it thanks any ways

Originally Posted by falconvan

Scoggins-Dickey has a good listing of them. I used a GM roller cam that I bought from them called the Ram Jet roller cam in a TBI rebuild and was really happy with the results. I think it was about $200.

well there many good cams out there and scoggins dickeys have some nice stuff as i am a dealer for some cams i could get him any thing at a good deal BUT he has no money to spend on a 200. cam even if i sold him one at my cost it to much money. this cam i have cost 30.00 he has that much thanks any ways

I have never had a lobe go flat on any cams I've installed over the years.
Guess I better knock on wood, But I've allways used plenty of cam lube,
run 10/30 for break in's and packed the oil pump with vaseline.
I did a cam for my Ex-father in law one time, sent him down to
the parts store with a exact list on the stuff to get.
He came back with all kinds of mismatched stuff, the guy said it was
on sale so he bought it. The guy was just trying to get rid of the stuff he
had, I wanted to go down there and pull the guy over the counter because I
had talked to the guy. Anyway I had to retard the cam by three teeth on the timming
chain to get it where it was supposed to be. Something must have fallen down
in the engine [piece of gasget or junk] because with in a week it wipe the main bearings out. He gave me the truck at 5pm on friday night, by 2am the engine was back in the truck and on the road headed for a car show in Illnois hauling a french fri stand.
Would have been done sooner but broke a main cap bolt and had to stop and go get a new one. And he made his 10 am starting time too!!! Kurt

i still use flat cams in some engines and long block them if i know they will get broke in right. but i have seen more then one wipe over the years. the last two engine in my shop wipe a flat lifter cam and i rebuilt them and went roller. i will not build a bbc with one in it. the kits are not that bad over the cost of picking junk out of the piston skrits and rebuilding the engine one more time i use strat wt oil to break the rings

My cleveland was a pain to set up for a roller cam.
I had to go in and grind the XXX's off the oil galley wall.
The roller lifters would have gotten snagged on them.
Kurt

the last 351C i built had a flat lifter cam in it and used joe gibbs beak in oil in it doing a 351 w going the same way on oil