Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: 3.1L corsica oil pan removal
          
   
   

Reply To Thread
Results 1 to 7 of 7
  1. #1
    projoe86's Avatar
    projoe86 is offline Registered User Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    spring lake
    Car Year, Make, Model: 96 chevy corsica
    Posts
    2

    3.1L corsica oil pan removal

     



    I've been trying to change the oil pump and for some reason the oil pan will not come loose no matter what I try. I've even went as far as using my air chisel ( and I know it's a big no no) but all else has failed. I only hope that some one out there will have some info that might help me out.

  2. #2
    lt1s10's Avatar
    lt1s10 is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    rustburg,
    Car Year, Make, Model: 1997 CHEVY.S10 LT1-350
    Posts
    4,093

    Re: 3.1L corsica oil pan removal

     



    Originally posted by projoe86
    I've been trying to change the oil pump and for some reason the oil pan will not come loose no matter what I try. I've even went as far as using my air chisel ( and I know it's a big no no) but all else has failed. I only hope that some one out there will have some info that might help me out.


    have you got the motor hanging and the cradle loose? if you have sounds like you got more bolts in the pan.
    Mike
    check my home page out!!!
    http://hometown.aol.com/kanhandco2/index.html




  3. #3
    drg84's Avatar
    drg84 is offline CHR Member Visit my Photo Gallery
    Join Date
    Sep 2003
    Location
    Dansville
    Car Year, Make, Model: 1996 Aurora Autobahn edition
    Posts
    1,201

    Lt1 has a point. raise the motor more and run your hand along the sides of the pan. if you dont feel anything, look for overhang by the ends of the pan.
    Right engine, Wrong Wheels

  4. #4
    Dwayne's Avatar
    Dwayne is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2004
    Location
    Gainesville
    Car Year, Make, Model: '81 X11
    Posts
    73

    What year Corsica? If it's an aluminum pan, it's cross-bolted into the main caps on the sides (mains 1,2,&3). Bolts are 15mm head (?) and have seals pan side.
    If it's tin, be sure to loosen/remove the front mount bracket or the pan won't drop down far enough to clear the mains.
    Hope this helps.

  5. #5
    SBC's Avatar
    SBC
    SBC is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2004
    Location
    Magnolia
    Car Year, Make, Model: 69 Chevy Nova 283 4-spd
    Posts
    443

    Hey projoe86 - found a similar thread here on CHR:
    Searched Yahoo - and it sent me back here!

    You're definately in the right place.

    Check this out!

    jramshu said - Just an update. This was a pain. Had to remove motor mounts(1 upper and 2 lower). Lift engine with jack. Hold rear frame up on stands. Remove pass. tire, tie rod, lower ball joint, serp belt, ac comp, starter, and a lot of plastic. Six oil pan to main bolts. And so on. Remove 4 bolts on frame and lower frame as low as possible. Then you can remove the pan thru the passenger side. Takes a whole 10 minutes to install new pump and a day and a half to get to it and put it back together.
    Bert
    Last edited by SBC; 06-21-2005 at 08:43 PM.

  6. #6
    projoe86's Avatar
    projoe86 is offline Registered User Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    spring lake
    Car Year, Make, Model: 96 chevy corsica
    Posts
    2

    Thanks guys for the help. And yes it's the aluminium pan.. SO it would seem I have a few more bolts to remove. again THANKS FOR YOUR HELP.

  7. #7
    R Pope is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    Eston
    Posts
    2,270

    May I suggest----high explosives???(Not a Corsica fan.)

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink