Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: Timing
          
   
   

Reply To Thread
Results 1 to 6 of 6
  1. #1
    canibalchicken's Avatar
    canibalchicken is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    spring
    Car Year, Make, Model: Hot Rod Suburban
    Posts
    142

    Timing

     



    Ok I have a 1973 SBC 350 with .040 over size bore. Gapless rings, 1.6 ratio roller rockers. Cam is .453 (I/E) w/ 230 duration. The top of the motor is 1993 TBI intake and heads. It has the computer controled distributor. Where would be my best starting point to set the timing?
    Chevys for life

  2. #2
    lt1s10's Avatar
    lt1s10 is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    rustburg,
    Car Year, Make, Model: 1997 CHEVY.S10 LT1-350
    Posts
    4,093

    Re: Timing

     



    Originally posted by canibalchicken
    Ok I have a 1973 SBC 350 with .040 over size bore. Gapless rings, 1.6 ratio roller rockers. Cam is .453 (I/E) w/ 230 duration. The top of the motor is 1993 TBI intake and heads. It has the computer controled distributor. Where would be my best starting point to set the timing?
    if the timing is computer controled there is a plug at the dist. you have to unpluge before you can set the timing. unplug the plug and sat the timing at 5 degrees, plug the plug back up and thats all you need to do.
    Mike
    check my home page out!!!
    http://hometown.aol.com/kanhandco2/index.html




  3. #3
    canibalchicken's Avatar
    canibalchicken is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    spring
    Car Year, Make, Model: Hot Rod Suburban
    Posts
    142

    Ok cool. I want that at 5 deg before top dead center correct. Also this plug I need to un plug. Is it the one that goes to the coil or to the main wiring harness?
    Chevys for life

  4. #4
    lt1s10's Avatar
    lt1s10 is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    rustburg,
    Car Year, Make, Model: 1997 CHEVY.S10 LT1-350
    Posts
    4,093

    Originally posted by canibalchicken
    Ok cool. I want that at 5 deg before top dead center correct. Also this plug I need to un plug. Is it the one that goes to the coil or to the main wiring harness?
    BTDC yes. i think its got 4 wires in it, but its close to the dist and its the one that after you unplug it, the motor will still run . if you unplug the wrong one the motor want run. i wish i could tell you more about it, but its one of those deals where if i was there i would know which one it is. if its any ? about if its the right plug when you unplug it and plug it back up the rpm's will change a lot, because you will be changing the timing so much. also about the timing after you set it and crank the motor up it dont do any good to move the timing after that because the computer will just put it back where it was. thought you might need to know that. the motor is runing right?

    ps it will be the plug going into the main harness.
    Last edited by lt1s10; 06-20-2005 at 08:31 PM.
    Mike
    check my home page out!!!
    http://hometown.aol.com/kanhandco2/index.html




  5. #5
    canibalchicken's Avatar
    canibalchicken is offline CHR Member Visit my Photo Gallery
    Join Date
    Jun 2005
    Location
    spring
    Car Year, Make, Model: Hot Rod Suburban
    Posts
    142

    the hot rod is running now. Going to start breaking in the engine tomorrow.

    Thanks
    I got it set on 5 deg btc. Fantastic!!
    Chevys for life

  6. #6
    lt1s10's Avatar
    lt1s10 is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2004
    Location
    rustburg,
    Car Year, Make, Model: 1997 CHEVY.S10 LT1-350
    Posts
    4,093

    thats great canibalchicken, good luck.
    Mike
    check my home page out!!!
    http://hometown.aol.com/kanhandco2/index.html




Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink