Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: wont start!
          
   
submit
   

Reply To Thread
Results 1 to 15 of 57

Hybrid View

threearmsinjune wont start! 11-18-2007, 12:03 PM
jerry clayton will it run on starting... 11-18-2007, 12:12 PM
threearmsinjune will not hit on ether, no... 11-18-2007, 12:14 PM
jerry clayton Also to set the timing there... 11-18-2007, 12:14 PM
threearmsinjune this wire is to set timing on... 11-18-2007, 12:17 PM
jerry clayton If the timing is set... 11-18-2007, 12:18 PM
jerry clayton If you have fuel air and... 11-18-2007, 12:25 PM
threearmsinjune this is a rebuild with the... 11-18-2007, 12:29 PM
jerry clayton you are probably mis... 11-18-2007, 12:36 PM
threearmsinjune all sensors are connected. ... 11-18-2007, 12:44 PM
threearmsinjune cam is timed 4 advanced over... 11-18-2007, 12:46 PM
threearmsinjune if the cam is too much would... 11-18-2007, 01:01 PM
threearmsinjune If the sensor is faulty... 11-18-2007, 05:25 PM
threearmsinjune good idea about the rings and... 11-18-2007, 01:17 PM
threearmsinjune cleaned plugs. shot of oil... 11-18-2007, 01:34 PM
threearmsinjune I am 6 btdc. I am still... 11-18-2007, 01:50 PM
threearmsinjune I am getting spark while... 11-18-2007, 02:16 PM
threearmsinjune Denny thanks. I think I need... 11-18-2007, 03:11 PM
jerry clayton I've been watching the Nascar... 11-18-2007, 03:01 PM
jerry clayton You said that it was the same... 11-18-2007, 03:07 PM
threearmsinjune This is a factory 350 TBI. ... 11-18-2007, 03:46 PM
jerry clayton Denny--I don't know on the... 11-18-2007, 03:21 PM
BigRedTrucker I think chevy made 350 tbi... 11-18-2007, 03:27 PM
jerry clayton I checked some of his... 11-18-2007, 03:46 PM
R Pope Trying to fire and then... 11-18-2007, 04:05 PM
threearmsinjune I ran into the thing with the... 11-18-2007, 04:12 PM
jerry clayton I see we both posted at the... 11-18-2007, 04:15 PM
jerry clayton I wish you had a... 11-18-2007, 04:35 PM
threearmsinjune Jerry, my name is Chris... 11-18-2007, 05:18 PM
jerry clayton Chris You could be correct... 11-18-2007, 05:57 PM
threearmsinjune coolant sensor is located... 11-18-2007, 06:31 PM
threearmsinjune no I have not! Could you... 11-18-2007, 06:32 PM
jerry clayton Denny--about the... 11-18-2007, 06:31 PM
jerry clayton those temp sensors for the... 11-18-2007, 06:35 PM
threearmsinjune i burn them off with... 11-18-2007, 06:52 PM
jerry clayton the tps has three wires --a 5... 11-18-2007, 06:39 PM
jerry clayton the dealers used to... 11-18-2007, 06:42 PM
jerry clayton too bad this forum doesn't... 11-18-2007, 06:45 PM
jerry clayton Chris here is the temp/ohms... 11-19-2007, 09:09 AM
threearmsinjune Denny And Jerry, After... 11-19-2007, 04:01 PM
threearmsinjune well the tps is not... 11-19-2007, 05:24 PM
threearmsinjune Direct test of TPS: input... 11-19-2007, 05:33 PM
threearmsinjune denny do you agree on... 11-19-2007, 05:36 PM
threearmsinjune I have cranking pressure now... 11-20-2007, 04:09 PM
BigRedTrucker Could be a vacuum leak too? 11-20-2007, 04:25 PM
threearmsinjune they are in order... 11-20-2007, 04:58 PM
threearmsinjune I burned the plugs off until... 11-20-2007, 05:10 PM
jerry clayton If you have compression, and... 11-20-2007, 05:32 PM
threearmsinjune out of phase? 11-20-2007, 05:41 PM
jerry clayton move the wires 180 11-20-2007, 07:03 PM
jerry clayton You don't have to move them... 11-20-2007, 07:05 PM
threearmsinjune Well I figured out why it... 11-29-2007, 04:20 PM
  1. 11-18-2007 06:35 PM #1
    jerry clayton's Avatar
    jerry clayton is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Feb 2006
    Location
    Bartlett
    Posts
    6,831

    those temp sensors for the computor have a standard ohm reading /temperature--if you have a manual it is probably listed in a chart
    Check the compression numbers---if they are way low it will probably indicate you need to look at cam timing
    Reply With Quote Reply With Quote
  2. 11-18-2007 06:52 PM #2
    threearmsinjune is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Oct 2006
    Location
    Indianapolis
    Car Year, Make, Model: 79 shovel, 65 pan
    Posts
    133

    i burn them off with oxy/acet. because at least I can make it fire when I want to!
    1989 GMC K2500
    Reply With Quote Reply With Quote
Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules

Links monetized by VigLink