Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: antifreeze or oil
          
   
   

Reply To Thread
Results 1 to 5 of 5
  1. 07-21-2010 03:38 PM #1
    larjones
    larjones is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Mar 2010
    Location
    massillon
    Car Year, Make, Model: 62 ford thunderbird convertible
    Posts
    34

    antifreeze or oil

     



    I have been notices I have a small leak around two inches in under the drivers side head. This is oil. Now if the head is leaking wouldnt it be antifreeze instead of oil. I think the leak is behind the intake corner and it is running down on the side of the block. I need some expert advice on this the dye I put end hasnt taken affect yet. This is a 62 fe390 engine and its a new short block and the heads were milled also. Larry
    Reply With Quote Reply With Quote
  3. 07-21-2010 06:08 PM #2
    Dave Severson
    Dave Severson is offline CHR Member/Contributor
    Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Madison
    Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
    Posts
    21,160

    Probably leaking where the intake meets the block??? FE's like to leak oil there, have to be very careful when installing the intake to keep it leak free!
    Yesterday is history, tomorrow is a mystery, Live for Today!
    Carroll Shelby

    Learning must be difficult for those who already know it all!!!!
    Reply With Quote Reply With Quote
  4. 07-22-2010 04:53 PM #3
    TheRoger
    TheRoger is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Jul 2010
    Location
    Toronto
    Posts
    5

    My 390 fe leaks all kinds of oil out of the intake. It looks like it's comign out of the head gasket, but it is from the intake and runs down.
    Reply With Quote Reply With Quote
  5. 07-22-2010 04:54 PM #4
    TheRoger
    TheRoger is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Jul 2010
    Location
    Toronto
    Posts
    5

    It is also a pain because you have to take the pushrods out in order to change the intake seal. It's a pain, I did it once already and held for only about six months. I used to drive her every day. Now I'm back to an old chevy, intake seal takes about 30 minutes to do.
    Reply With Quote Reply With Quote
  6. 08-08-2010 03:41 PM #5
    hotrodstude
    hotrodstude is offline CHR Member
    Visit my Photo Gallery
    Join Date
    Jul 2009
    Location
    pendergrass
    Car Year, Make, Model: 2006,ford,f-150,v-6,5-speed manual
    Posts
    245

    did you have the intake milled???you stated that the heards were milled.its possible that the ports and water ports are not lining up.
    Reply With Quote Reply With Quote
Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules

Links monetized by VigLink