Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: 1955-1959 chevrolet big window trucks
          
   
   

Reply To Thread
Results 1 to 6 of 6
  1. #1
    badbrad83's Avatar
    badbrad83 is offline Registered User Visit my Photo Gallery
    Join Date
    Dec 2004
    Location
    st. george
    Car Year, Make, Model: 1957 chevrolet pickup pro street
    Posts
    2

    1955-1959 chevrolet big window trucks

     



    just a silly question here. does anyone here have any experance with switching a small window pickup to a big back window? i started this project with no real preferance but the further i get into it the more i think i want a big back window this far along i dont realy want to scrap the cab i have. any insight would be great
    thanks brad

  2. #2
    Dave Severson is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Madison
    Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
    Posts
    21,160

    Never have done it, but it shouldn't be too bad of a project. I think if you were to cut the back of a big window cab apart at the seams, you should be able to do the same with the small window cab to put it in. When you cut the back out of the keeper cab, you should build some good supports to hold the roof and the side of the cab in place so aligning everything on the cab doesn't turn into a nightmare..... If taking it apart at the seams won't work, then cut about 3" outside of the big window, flange the cut line, and cut the small cab back window out and put the big back in. Use a hard paper or cardboard pattern to make your cuts and remember that the opening on the small cab will have to be 1/2" smaller all the way around to lay on the flange you made on the big back window cab section you cut out!!!!
    Last edited by Dave Severson; 02-04-2006 at 05:19 AM.
    Yesterday is history, tomorrow is a mystery, Live for Today!
    Carroll Shelby

    Learning must be difficult for those who already know it all!!!!

  3. #3
    DynoDon is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2001
    Location
    Tulsa
    Car Year, Make, Model: 55 Chevy Pick-up
    Posts
    99

    Gee, I kind of like the small window myself

  4. #4
    shine's Avatar
    shine is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2003
    Location
    bluff dale texas
    Car Year, Make, Model: 47 inderweed
    Posts
    2,136

    seen it tried. it's the build from hell. it is much easier to fix the big window cab with parts from the small window. jmo

  5. #5
    deuce4papa is offline CHR Member Visit my Photo Gallery
    Join Date
    Apr 2005
    Location
    Ardmore
    Car Year, Make, Model: 32 Ford
    Posts
    255

    Yeah. I started this very same project myself. I found a complete cab that was in better condition than my original small window cab after I had cut out a big window cab section from another donor cab to do this project. I was going to use the drip rail seam and the factory seam at the back of the doors for the outer panel, and would have had to make a seam across the full width of the cab for the lower edge of the outer panel. I would have had to make a seam at the top for the inner panel. You are working with both an outer and inner panel here. The big window cab has extra braces welded in by the factory that reinforce the upper corner of the door opening. You will not be able to weld these in. As you can see, this is going to be very labor intensive. Hope this helps.

  6. #6
    Dave Severson is offline CHR Member/Contributor Visit my Photo Gallery
    Join Date
    Jul 2003
    Location
    Madison
    Car Year, Make, Model: '67 Ranchero, '57 Chevy, '82 Camaro,
    Posts
    21,160

    Yup, very labor intensive !!!! But if it was easy, everybody would be doing it!!!!
    Yesterday is history, tomorrow is a mystery, Live for Today!
    Carroll Shelby

    Learning must be difficult for those who already know it all!!!!

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink