Thread: s10 rear behind 5.0 mustang motor

Tweet

what do you think. would an s10 pick up rear hold up against a stock 5.0 fuelinjected mustang motor and and aod trans? i`ll put camaro disk brakes on the back if i do decide to use it. it has 4.10 i think are stock for a 4 banger s10.

Depends on how hard you are going to be pounding on it. If it's a posi and you're running slicks and good traction, not long. For street use and an open differential, probably work ok.

I have an S10 rearend under the roadster pickup---works great. Granted, the abuse it takes from my weary old 305 doesn't really compare to a 5 litre, but I know in my rpu that it will never hook up enough to hurt it amyways.

We twisted the pinion off with a 350 in an S10. Not a really tough rear end.

gonna be a street rod. no burn outs. gonna turn some big wheels be bagged and such i can get one for free and its the right width. the one i pulled from my parts lincoln is way to wide and i would have to get it shortened. just trying to get some opinons before i get it.

Under those circumstances and usage, you should have no problem. Lots of S10's running around with V8 swaps. I am using one in my T and in my '39, one has a 350 Chevy, the other a 406 Olds, and know I can't do smokey burnouts all the time, but that is not what I plan on doing anyway.

S10's are really a nice fit for streetrods, plentiful, and consequently pretty cheap.

Don

At 50 here it will be really hard for me not to do some burn outs . Have you thought about a 8.8 nice up grade and some narrow ones in the early 90 rangers. U pull it yards around here sell whole rear ends for $50 .

You could use a '87-'93 Mustang 8.8 and if you get it out of a GT Mustang you get a locker. All '87-'93 Mustangs came with 4 lug, If you use 2 driver side axles from a Ranger, or use Astro van's 2 pass side axles you will get 5lug. Around here axles go for about $25.00, and rear ends are about $25.00- $75.00.
Bolt on Lincoln rear disk mounting plates reverse side and backwards and rotors, then you can use Mark III caliptors and have disk also.

Just another idea.

Pat

Great info Hemi . One thought will the 94 to 98 Mustang rear disc mount right up to all 8.8's

i`m a go to the bone yard tomorrow and look for the mustang rear if no luck than s10 it is. although a locker would be nice, but i`m not the speed racer type. slow and low so the ladys get a good look

I am building a S10 and the guys on the S10 sites say that 300 HP with hard launching will break them. Its the hard launches (usually slicks) when they break.
Some of the Exployers and others have 8.8" rears. They stick out about 3" on each side but maybe backset wheels would help here. The only change is the pinion yoke is different and napa has the right one to fit it together.
But there are some 10 sec. S10's with the original 7.5" rears but should be 'beefed up' if abused.

Originally Posted by bluestang67

Great info Hemi . One thought will the 94 to 98 Mustang rear disc mount right up to all 8.8's

Sorry, I've been busy, Try looking here for your 8.8 needs

---> http://www.mustangforums.com/searchp...mitbutton=+OK+


Pat

Sorry, it won't work now unless you log in!!!!

If you go there, it has a Lot of disk brake info, just search disk brakes.

Pat

Most 4X4 Ford rangers & Bronco II's have 8.8 And some have posi's in them with lower gear ratio's than the Mustangs.....With 5 on 4 1/2 lug pattern. They also were leaf spring mounted, they are easier to "clean-up" to use for 4-link.

The down side is the flange mounted rear yoke on the driveshaft so snag the drive shaft also.

Nice thing about the 8.8 is the wide range of after-market for them. I put a 8.8 in a Jeep that came out of a 99 Explorer. I put a 4.56 set of Yukon gears and a Detroit locker in it. That was a beast of a rear end. I beat the heck out of it and it had the disk brakes.