Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: What is this???.......
          
   
   

Reply To Thread
Results 1 to 8 of 8
  1. #1
    knucklehead's Avatar
    knucklehead is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2006
    Location
    714
    Car Year, Make, Model: 55 Belair, 53 Ranchwagon, 49 coupe
    Posts
    80

    Question What is this???.......

     



    What is this. It is inline on the red wire from the positive battery cable.

    This is my buddy's ride, hes in vegas and is having charging problems, replaced battery, didnt help, replaced alternator, didnt help.

    This "thing" was covered up and he didnt notice it at first, he thinks it could be bad, and wants to get rid of it and try.....but i told him dont try yet, it could be a resistor.

    The entire set up use to charge and work fine, now hes getting electrical gremlins.

    Its 59 chevy pickem up, new wire harness, A/C, 350 chevy motor, 350trans, it has a satallite radio reciever no amps or anything crazy, i dont think it has HEI which makes me think it could be a resistor........but i just dont know what it is
    Attached Images
    If it aint broke, fix it till it is.

  2. #2
    NTFDAY's Avatar
    NTFDAY is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2003
    Location
    Springfield
    Car Year, Make, Model: '66 Mustang, 76 Corvette
    Posts
    5,379

    It could be a very high amp fuse and/or circuit breaker.
    Ken Thomas
    NoT FaDe AwaY and the music didn't die
    The simplest road is usually the last one sought
    Wild Willie & AA/FA's The greatest show in drag racing

  3. #3
    Itoldyouso's Avatar
    Itoldyouso is offline CHR Member Visit my Photo Gallery
    Join Date
    Jan 2006
    Location
    fort myers
    Car Year, Make, Model: '27 ford/'39 dodge/ '23 t
    Posts
    11,033

    Yep, circuit breaker. Probably about 40 amp.

    Don

  4. #4
    knucklehead's Avatar
    knucklehead is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2006
    Location
    714
    Car Year, Make, Model: 55 Belair, 53 Ranchwagon, 49 coupe
    Posts
    80

    Thanks you guys, this will defenitly help cuz he bought the truck already built and lost the contact info to the guy that built it , I appreciate the quick responses....thanks


    Heres a pic of the culprit
    Attached Images
    If it aint broke, fix it till it is.

  5. #5
    NTFDAY's Avatar
    NTFDAY is offline CHR Member Visit my Photo Gallery
    Join Date
    Aug 2003
    Location
    Springfield
    Car Year, Make, Model: '66 Mustang, 76 Corvette
    Posts
    5,379

    That's a nice looking truck.
    After looking at the picture of the circuit breaker you posted I noticed that the hook up from the battery clamp to the breaker looks a little toasty. That to me indicates a bad circuit and before you do anything else you should find the cause and eliminate it. That is way to pretty of a truck to see it burn to the ground.
    Ken Thomas
    NoT FaDe AwaY and the music didn't die
    The simplest road is usually the last one sought
    Wild Willie & AA/FA's The greatest show in drag racing

  6. #6
    techinspector1's Avatar
    techinspector1 is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    Zephyrhills, Florida, USA
    Car Year, Make, Model: '32 Henway
    Posts
    12,423

    Having been there, done that, I can almost guarantee that you don't have good grounds, especially after seeing all the fresh new paint. Using 2 new ground straps, grind the paint off down to bare, shiny metal on the firewall somewhere and grind a spot on the frame. Make sure these ground-off places are large enough so that the ground strap isn't laying on any paint. Either sheet-metal screw the cables down or drill through and use a bolt and nut. Same deal with the motor. Find a place on the block where you can attach the other cable and run it to the connection on the frame where the firewall cable terminates. After you've done this, coat both the outer and inner sides of the hole/screw/bolt/nut whatever on each cable end with RTV to completely seal both sides of each connection from atmosphere and water being splashed up from the road.
    PLANET EARTH, INSANE ASYLUM FOR THE UNIVERSE.

  7. #7
    knucklehead's Avatar
    knucklehead is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2006
    Location
    714
    Car Year, Make, Model: 55 Belair, 53 Ranchwagon, 49 coupe
    Posts
    80

    Quote Originally Posted by NTFDAY
    That's a nice looking truck.
    After looking at the picture of the circuit breaker you posted I noticed that the hook up from the battery clamp to the breaker looks a little toasty. That to me indicates a bad circuit and before you do anything else you should find the cause and eliminate it. That is way to pretty of a truck to see it burn to the ground.

    thanks for replying, I should have mentioned that the black stuff on the wire, is some type of sealant, it was covered in a round tube and sealed on one end.

    It is a nice trcuk and hes been really happy with it, the gremlins are recent. ya his plan is to keep it off the road until it is fixed properly. hes trying to get the repairs completed by begingin of may, i guess theres a rod run in northern nevada hes heading to, it will be my first time there.
    If it aint broke, fix it till it is.

  8. #8
    knucklehead's Avatar
    knucklehead is offline CHR Member Visit my Photo Gallery
    Join Date
    Dec 2006
    Location
    714
    Car Year, Make, Model: 55 Belair, 53 Ranchwagon, 49 coupe
    Posts
    80

    Quote Originally Posted by techinspector1
    Having been there, done that, I can almost guarantee that you don't have good grounds, especially after seeing all the fresh new paint. Using 2 new ground straps, grind the paint off down to bare, shiny metal on the firewall somewhere and grind a spot on the frame. Make sure these ground-off places are large enough so that the ground strap isn't laying on any paint. Either sheet-metal screw the cables down or drill through and use a bolt and nut. Same deal with the motor. Find a place on the block where you can attach the other cable and run it to the connection on the frame where the firewall cable terminates. After you've done this, coat both the outer and inner sides of the hole/screw/bolt/nut whatever on each cable end with RTV to completely seal both sides of each connection from atmosphere and water being splashed up from the road.

    You know your right about the paint, it is really thick......and nice, i noticed that while poking around under there. This is all great info, thanks for the reply.



    when its figured out and repaired i'll post an update
    If it aint broke, fix it till it is.

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink