Thread: Battery or Alternator bad?
-
08-15-2008 12:11 AM #16
one more thing to check run a jumper wire from the alt case to ground the alt has to br grounded I had a couple of times diy ers came to my shop after puting in new motors thr paint was so thick it would not ground that will make you scrach your head a few times ted
-
Advertising
- Google Adsense
- REGISTERED USERS DO NOT SEE THIS AD
-
08-15-2008 07:27 AM #17
Guys, great info and I have plenty to do this weekend because of it!
Took my alternator to AutoZone after work last night and it tested GOOD too. Got another guy that was interested in Hot Rods.........Like finding gold. Right!? It past the test, however, he did tell me that since it's off the car it only tests to see if it's putting our amps. NOT how many..........He said I should put the car back together and bring it down and he'll wheel out the cart that will tell us exactly how many amps it's putting out. He works all day Saturday so we will test it at idle, then at 2,000 rpm and the car HOT. See what we get there and then turn lights radio and electric fan on etc!
My luck is bad! Bought a nice new digital volt meter there last night for $36. Took it home and put it on my battery, set at 20 volts setting on the dial. BOTH the ground and positive wires hot super hot and almost melted! Would give no reading at all just stayed at 0.00. Used my old dial voltmeter (non digital) and worked just fine. Did my car battery and truck battery. Same result on both.32 Ford
Des Moines, Iowa
Website- http://s104.photobucket.com/albums/m...012/32%20Ford/
-
08-15-2008 12:50 PM #18
Originally Posted by bucs012
I know a lot of people love those one wire delcos but I would wire in a regulator to run an old style Ford alternator personally.
-
08-15-2008 04:56 PM #19
I would suspect a bad starter... could have dirty brushes or contacts and a weak one gets weaker with heat. Sounds like your battery and alternator are both okay. I've had similar troubles before that turned out to be a loose (not tight) ground connection to the battery... as was mentioned before, check your ground... from battery to frame and battery to engine block...
on your new voltmeter, if you had the settings or the leads setup to read current (Amps) you would have a short and burn your leads measuring across the battery posts...
goode luck,
-Chris
-
08-15-2008 08:08 PM #20
I must ask. Were you guys foolin with me???? With my car off, some of you told me to keep my battery ground cable on battery. Unhook my positive cable from the post. Run one end of my 6 or 12 volt circuit test light to the battery + post then the other end of the circuit test light to the + battery cable. If the light lights up it meant I have a current draw from my car, draining my battery......And I need to find it by pulling fuses till it goes out. Well, the light lit up when I did this. Isn't this the same thing as having the cable hooked to the post thus of course it's getting power?
I tried this same test on my 63 Nova, my 2005 ram truck and my wifes 07 Pacifica. All 3 times the light lit up when I do the test.
My battery tested at 12.6 volts this morning and again tonight when I got home from work still outside the car NOT hooked up to anything. I put the car back together. Started the car up and running at idle of 1,000 or 2,000 rpm's I get 14.5 to 14.65 volts at the battery even when my electric fan kicks on. All sounds good. Right?
Went for a nice drive with fan running through a few cycles of on/off. Got home and turned car off to check the battery again and now it is higher voltage at 12.84. Great, right?
So tonight I am leaving it all hooked up and seeing what my voltage reading is in the morning after having set hooked up in the car for 12 hours.Last edited by bucs012; 08-15-2008 at 08:12 PM.
32 Ford
Des Moines, Iowa
Website- http://s104.photobucket.com/albums/m...012/32%20Ford/
-
08-16-2008 11:35 PM #21
Nope, I'm not goonin ya! Ok, the test light your using, is it an incandescent bulb? ( Can't use an LED type for this type of test. )Did you have the door open at the time of the test? That would cause a draw, because the interior light would be on. How about the hood, have a light that comes on when it's open, or the trunk lid, same thing would happen. Everything has to be off, that would normally be off, including the key switch. Any of these would cause a closed circuit and make your test light come on. The one thing that may be getting you, is the plug on the alt that plugs into the regulator. Unplug it, to eliminate it, while you do your test. If everything is off, and pulling the fuses won't make the light go out, you have one of three things happening. 1. The circuit that is involved isn't fused, or 2. you have a short on the positive side somewhere, ( pinched or wire rubbed bare ) or 3. an item isn't being shut off with the key switch. ( Electric fuel pump? Stuck brake light switch? Glove box light? Radio-tape-CD player? ) With the test light hooked up inline ( in series ) on the positive cable, any, and all power flow will have to go through it. It will only light up if there is flow. Just have to keep hunting, feel and smell for anything getting hot. Now isn't being a mechanic fun. I've been doing this stuff for a lot of years, and most times these things are simple and stupid. Well, they are once you find them. SniperLast edited by Sniper; 08-16-2008 at 11:43 PM.
-
08-17-2008 03:53 AM #22
Originally Posted by Sniper
Very often I find the draw on a GM to be inside the alternator, shorted internal regulator I suppose. They can even still charge ok and do that.
-
08-17-2008 09:04 AM #23
Originally Posted by willowbilly3
And a Happy Birthday Wish for Mr. Spears. Hope you can have a great one. :)
A little bird