Thread: Hose Connector?

Tweet

Anyone have a source for a couple of radiator hose connectors, 1.5" and 1.75" ID hose? Speedway has these http://www.speedwaymotors.com/Straig...tors,8936.html but I'm really needing something more like three to four inches long. I'm going to shorten the straight run on an upper formed hose, and shorten and turn one end of the lower hose, using Gates shrink clamps with the ends butted together. I like the idea of a bead on the ends to eliminate slip, but I suppose exhaust pipe would work, with aluminum or stainless being even better.

i made tubes for upper and lower out of steel and alum with no beads on the ends never lost one Burns and other sell tube in s steel or alum. alum will not be hard to roll the bead in with the s steel i would just tig a bead on it i allways just used band clamps and turn them so you do not see the screw head. i trim the clamp for hose size so there is no tail hang off the clamp so when done you only see the band thats all

Originally Posted by pat mccarthy

i made tubes for upper and lower out of steel and alum with no beads on the ends never lost one Burns and other sell tube in s steel or alum. alum will not be hard to roll the bead in with the s steel i would just tig a bead on it i allways just used band clamps and turn them so you do not see the screw head. i trim the clamp for hose size so there is no tail hang off the clamp so when done you only see the band thats all

Pat,
I'm thinking that a piece of exhaust pipe should work fine. With a good 50/50 mix of antifreeze they should never corrode, and I really don't think that they will be captured between the inlet/outlet fittings, so not much way they can go anywhere. I've got two hoses that are close, but need a bit of tweaking to fit right. I may check the plumbing dept at Lowe's tomorrow to see if they have anything that might work...

yep the mild steel ex tube worked fine with 50/50 mix you could check out the sink drains

I had a steel connector without beads in the upper hose on my Olds. After blowing the hose twice I bought the Speedway connector. No problem since.

Roger - are you trying to connect that odd angled SB Ford water outlet to the radiator? If so, there are 90* versions available that will make life easier - but I'll be dammed if I recall where mine came from - might be the Ford SVT.

Lowes - look in the irrigation plumbing. I seem to recall some aluminum fittings similar to the PEX (Home Depot locally, for me has a better selection of that kind of 'stuff', but if there isn't one near you.....)

Originally Posted by IC2

Roger - are you trying to connect that odd angled SB Ford water outlet to the radiator? If so, there are 90* versions available that will make life easier - but I'll be dammed if I recall where mine came from - might be the Ford SVT.

Lowes - look in the irrigation plumbing. I seem to recall some aluminum fittings similar to the PEX (Home Depot locally, for me has a better selection of that kind of 'stuff', but if there isn't one near you.....)

Dave,
Yes, the water neck points up ~30 degrees, my radiator neck tilts down ~10 degrees (radiator laid back), I have ~2" horizontal offset and the vertical CTC on hoses is ~10". I took a hose with a "flat Z" shape, angles about 45 but the vertical was too long by about 2". Found a 1.5" thinwall sink drain 4" long that fits perfect to sleeve the hose. Then I started trimming ends to get the fit perfect and took too much off of the bottom one which put the hose into the throttle cable. Looks like I'm going to buy another hose like I had and try again.

Originally Posted by Wingman9

I had a steel connector without beads in the upper hose on my Olds. After blowing the hose twice I bought the Speedway connector. No problem since.

My hoses are pretty short and very constrained so I am hoping that the smooth tube works for me. My problem is I do not have 6" of straight run in either hose to use the Speedway fittings. The 4" that I used makes the hoses very hard to flex into place. I will definitely watch them for the first season to see if they slip any. I would like to find a shorter beaded connector.l

This is a SBF 90* and with a Cool Flex hose:

(and it really isn't that dusty any longer)