Welcome to Club Hot Rod!  The premier site for everything to do with Hot Rod, Customs, Low Riders, Rat Rods, and more. 

  •  » Members from all over the US and the world!
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and hundreds of thousands of posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

 

Thread: looking for info about updating to dual reservoir on stock brakes on 66 GMC
          
   
   

Reply To Thread
Results 1 to 5 of 5
  1. #1
    twoblularry's Avatar
    twoblularry is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2006
    Location
    hutchinson
    Car Year, Make, Model: 66 gmc swb 327,turbo350
    Posts
    26

    looking for info about updating to dual reservoir on stock brakes on 66 GMC

     



    I have been trying get the brakes upgraded on my 66 GMC, I have bolted on a 68 chevy dual reservoir master cylinder, and split the brakes front to rear. I have not installed a proportioning valve. the brakes work but have to be pumped once to get it to stop, my questions are, will I need to get prop. valve, will I need residual valve?? every one says put discs on, I didnt want to buy the spindles and all the other stuff, I wanted to keep the drums. it acts like there is air in the lines but I have Bled them several times.
    the stock master cyl. worked good but wanted the added safety of the dual reservoir and was hoping that I could keep it low budget as possible. anyone with advice or experienced this swap please fill me in.
    here is the Skinny on my truck. 68 327, 600 edelbrock carb, performer RPM manifold,doug thorley headers, turbo 350 built for street, 373 posi rear, all the wheel cyl have been replaced, 68 truck master cyl.
    thanks in advance
    twoblularry

  2. #2
    ted dehaan's Avatar
    ted dehaan is offline CHR Member Visit my Photo Gallery
    Join Date
    May 2003
    Location
    whittier ca.
    Car Year, Make, Model: 32ford5w,60fordstarliner,55chevy65corvai
    Posts
    645

    did you bench bleed the m/c if not they can be vary hard to get all the air out if you didn't get a bench bleeder at the parts store they only cost a few bucks it's hard to get all the air out on the truck because the pedal wont let the piston have full stroke that would be my first thought .....ted
    I'LL KEEP MY PROPERTY, MY MONEY, MY FREEDOM, AND MY GUNS, AND YOU CAN KEEP THE CHANGE------ THE PROBLEM WITH LIBERALISM IS SOONER OR LATER YOU RUN OUT OF OTHER PEOPLES MONEY margaret thacher 1984

  3. #3
    twoblularry's Avatar
    twoblularry is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2006
    Location
    hutchinson
    Car Year, Make, Model: 66 gmc swb 327,turbo350
    Posts
    26

    i did bench bleed, and then did it again after i mounted it in truck with the plastic fittings and lines. do either of you think i need proportioning valves?? I will take of the M/C and rebleed it start over..
    I adjusted the brake shoes till they drag then back them off a couple clicks. in 81' I was top of my class in votech on brakes, front ends, and auto trannys. but been alot of crazy living since then and my memory isnt what it used to be.
    thanks again
    twoblu larry

  4. #4
    twoblularry's Avatar
    twoblularry is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2006
    Location
    hutchinson
    Car Year, Make, Model: 66 gmc swb 327,turbo350
    Posts
    26

    thanks guys, I will check it out, could u post correct way to adjust brakes??
    thanks
    twoblu larry

  5. #5
    twoblularry's Avatar
    twoblularry is offline CHR Member Visit my Photo Gallery
    Join Date
    Nov 2006
    Location
    hutchinson
    Car Year, Make, Model: 66 gmc swb 327,turbo350
    Posts
    26

    the adjustments was the problem, i adjusted them as suggested by the above post and it fixed the problem. thanks.
    twoblu

Reply To Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Links monetized by VigLink